Pool heater installation and replacement in Las Vegas, Henderson and Mesquite. Gas heaters, heat pumps and pool chillers, sized for Southern Nevada’s climate.
The desert cools off hard. Using the National Weather Service 1991 to 2020 normals for Las Vegas, the average overnight low is 47.3 F in November, 39.6 F in December, 40.5 F in January, 44.1 F in February and 50.5 F in March. Daytime highs recover quickly, which is why the valley feels mild in winter. A pool does not care about the afternoon. It is a large thermal mass sitting outdoors for sixteen hours of darkness, losing heat the entire time.
That is the mechanism most homeowners miss. A pool does not get cold because the days are cold. It gets cold because the nights are, and because evaporation never stops in low humidity. The US Department of Energy states it plainly: evaporation is by far the largest source of pool energy loss.
Southern Nevada makes that worse than almost anywhere. Evaporation accelerates with low humidity, moving air and a warm water surface, and this valley supplies all three for most of the year. Every gallon that leaves your pool as vapour takes a substantial amount of heat with it. A pool in a humid climate holds its temperature far better than an identical pool here, which is why heating advice written for Florida does not transfer. Which is also why the first conversation we have about heating is usually not about a heater at all.
The Department of Energy’s position on this is unambiguous: covering a pool when it is not in use is the single most effective means of reducing pool heating costs, with savings of 50 to 70 percent possible. A cover also reduces the make-up water a pool needs by 30 to 50 percent and chemical consumption by 35 to 60 percent.
In a valley under permanent water conservation pressure, that make-up water figure carries weight on its own, independent of comfort. Less evaporation means less refilling, and less refilling means less of our hard Colorado River water concentrating in your pool over time.
We treat a cover as part of the heating system rather than an accessory. A covered pool holds the heat you put into it overnight, which means the heater runs to maintain rather than to recover. In practice that often lets us specify a smaller unit than an uncovered pool of the same size would need, and the pool reaches temperature faster.
One tradeoff worth knowing: a cover blocks some solar gain. A transparent bubble cover reduces the solar energy a pool absorbs by 5 to 15 percent, and a fully opaque cover by 20 to 40 percent. In a climate with this much sun, that is a real consideration in the shoulder months, and it is part of how we choose the cover type with you. A pool that is covered all day in March gives back some of what it saves overnight.
We fit and supply pool covers as part of heating work, including safety covers where there are children or pets in the household.
A gas heater burns natural gas in a combustion chamber and transfers that heat to water moving through the system on its way back to the pool. The Department of Energy describes gas heaters as ideal for quickly heating pools, and notes they can maintain any desired temperature regardless of the weather or climate, which makes them a good choice for pools used periodically rather than continuously.
That last point is the real decision driver here. If you want the pool warm this weekend because family is in town, and it is 41 F overnight, a gas heater does that and nothing else will. It does not care what the air temperature is, it does not slow down in January, and it brings a spa up to temperature in a timeframe measured in minutes rather than hours.
Edgewater installs the Jandy JXi line, which you can see alongside the rest of the Jandy equipment we carry. It comes in 200,000, 260,000 and 399,000 BTU natural gas models, at 83 to 84 percent thermal efficiency depending on model and heat exchanger, with a low-NOx design and a cabinet that fits on a two foot by two foot pad. That footprint matters more than it sounds on a crowded Las Vegas equipment pad where the original builder left no room to grow.
The JXi also communicates with Jandy AquaLink and iAquaLink controls, which is the difference between a heater you walk out to switch on and a heater that has the spa at temperature before you get home. If you are installing a heater and considering pool automation, doing both at once is considerably less work than doing them a year apart.
Sizing is not guesswork. The Department of Energy publishes the formula: pool surface area multiplied by the temperature rise you want multiplied by 12 gives the required BTU per hour output, assuming roughly a one degree per hour rise. Multiply by 1.5 for a one and a half degree rise, or by 2 for two degrees an hour. We run that calculation against your actual pool, your actual target temperature, and how fast you want to get there.
A heat pump does not make heat. It moves it. A fan pulls outside air across an evaporator coil, refrigerant absorbs heat from that air, a compressor concentrates it, and a condenser hands it to the pool water. Because it is relocating heat that already exists rather than burning fuel to create it, it does far more with the same energy.
Efficiency is measured as coefficient of performance, or COP. The Department of Energy puts typical pool heat pump COPs at 3.0 to 7.0, which works out to 300 to 700 percent efficiency. For comparison, a gas heater running at 84 percent thermal efficiency is, by definition, under 100. That gap is why a heat pump is the quieter long-term choice for a household that swims regularly.
The catch is air temperature. The Department of Energy’s guidance is that heat pump pool heaters work efficiently as long as the outside temperature remains above the 45 to 50 F range. Look back at the Las Vegas normals: November, December, January and February all average overnight lows at or below that band.
This is not a reason to rule out a heat pump in Las Vegas. It is a reason to be honest about what it will do. A heat pump here performs excellently from roughly March through November, which is most of the swimming year, and loses ground in deep winter when the air it is drawing from has less heat to give.
Jandy publishes the effect directly on its JE series rather than hiding it. The JE3000TR is rated at 130,000 BTU and a COP of 6.0 under standard test conditions, and the same unit rates 86,000 BTU and a COP of about 4.0 to 4.2 when tested at 50 F air. Same machine, colder air, roughly a third less output. That is the honest shape of the technology, and any installer who tells you otherwise is not being straight with you.
For a household that swims most of the year and wants the lowest energy draw, a heat pump is usually the right answer. For a household that wants the pool hot on demand in January, it is not. For a household that wants both, the answer is sometimes a heat pump as the workhorse with a gas heater for the cold snaps, and sometimes a reverse-cycle unit, which is the next section.
Heating is only half the problem in this valley, and the half nobody plans for is the one that arrives in July.
In July the Las Vegas average high is 104.5 F and the average overnight low is 82.0 F. In August it is 102.8 and 80.6. Two full months where the air does not drop below 80 degrees overnight, on average, across a thirty year record.
A pool cannot shed heat into air that warm. It absorbs sun all day and has nowhere to put it after dark, so it accumulates. By late July a lot of Las Vegas pools stop being refreshing and start being a warm bath, which is the exact moment a family most wants to use one. People who have never owned a pool here are usually surprised by this. People who have owned one for three summers already know.
A reverse-cycle heat pump solves it by running the refrigeration cycle backwards, pulling heat out of the pool water and rejecting it to the outside air. Jandy builds this into the JE3000TR and the VersaTemp line, and describes the reversing models as able to cool your pool during the hot summer months. One machine, both directions.
In this climate that is a more sensible purchase than a heater alone, and it changes the shape of the decision. Instead of choosing equipment that is useful for five months, you are choosing equipment that is useful for ten.
If you are replacing a failed heater anyway, this is the moment to decide whether the replacement should also chill. Adding the capability later means replacing the unit again, which is why we raise it on every heater replacement even when the customer called about winter.
Solar collectors pump pool water through panels, usually roof-mounted, and return it warmer. A sensor and a diverter valve send water to the collectors only when the collectors are hotter than the pool, and bypass them otherwise, so the system never works against you.
Southern Nevada’s solar resource is about as good as it gets anywhere in the United States, so the input side is not the limitation. The limitation is structural: a solar collector only adds heat while it is warmer than the pool, which means sunny hours. It will not bring a pool up on a cold January night, and it does nothing at 5am in any month.
The Department of Energy’s sizing guidance is that collector surface area should equal 50 to 100 percent of the pool’s surface area. On a typical valley home that is a meaningful amount of roof, and roof orientation, shading and structural capacity all have to be assessed before it is a real option.
There is an interesting desert footnote in the DOE guidance worth knowing: in hot climates, solar collectors can be run at night to cool the pool, because the panels radiate heat to the night sky. That is a lower-tech version of the chiller idea above, and on some properties it is enough.
In practice we see solar work best in Las Vegas as a season extender paired with a cover, or alongside a gas heater that handles the cold snaps the panels cannot reach.
Homeowners almost always describe their pool in gallons, and almost every heater sizing conversation starts by converting that back to surface area.
The reason is physical. Heat leaves a pool through its surface, by evaporation and by radiation to the sky. A deep pool and a shallow pool with the same surface area lose heat at roughly the same rate. The deep one simply takes longer to warm up in the first place, because there is more water to raise.
So surface area drives the size of heater you need to hold a temperature, and volume drives how long the first heat-up takes. Both matter, and they answer different questions. A long narrow lap pool and a compact freeform pool of the same volume are not the same heating job.
Other things that change the calculation on a real property:
We run the numbers on site with your equipment pad in front of us, not from a phone call.
If you have an attached spa, it changes the recommendation, and it is a common reason households end up with gas even when a heat pump would otherwise suit them.
A spa is small and wants to go from ambient to around 102 F on demand. A heat pump raises temperature gently over hours, which is exactly wrong for a spa you decided to use twenty minutes ago. A gas heater is built for that job.
On a combined pool and spa system, the valves determine which body of water the heater serves, and automation is what moves them without anyone walking outside. That is the single most common reason our customers add pool automation at the same time as a heater: being able to start the spa from the house, or from the car, is the difference between using it and not.
If a spa is in your plans but not yet built, tell us at the heating stage. Sizing a heater that can serve a future spa is straightforward. Replacing an undersized heater two years later is not.
Most of the heater calls we take are not planned upgrades. They are a heater that stopped working, usually on the first cold weekend of the year when everyone discovers it at once.
Worth watching for before that happens:
Hard water accelerates all of this. Scale forming inside a heat exchanger insulates it, which makes the heater work harder for less transfer and shortens its life. In 16 grain valley water that is a normal aging process rather than a defect, and it is one more argument for keeping water chemistry in range year round. We cover the chemistry side on our pool maintenance page.
If your heater is at the end of its life, a replacement is also the easiest moment to reconsider the whole approach: gas or heat pump, heat only or heat and chill, manual or automated. Those options are simple to choose at replacement and far harder to revisit once a new unit is installed and plumbed.
Heater work is permitted work, and the reason is almost always the gas line rather than the heater itself.
In the City of Las Vegas, the Building and Safety Division’s homeowner permit guide requires a permit to install, alter or repair gas piping between the meter and any appliance, indoors or outdoors, and it names a pool heater specifically. The city’s Swimming Pool Guideline goes further: mechanical plans have to show the heater’s type and size along with its venting and combustion air provisions, and gas line details have to show size, length, material and routing from the meter to the heater. On a new pool, the heater and any fire features fall within the scope of the pool permit itself. Gas line work requires a specifically licensed contractor, and the plumbing plans must be signed by that contractor. Building and Safety can be reached at 702-229-6251.
In the City of Henderson, the residential pool inspection sequence includes a gas heater installation inspection, a pool gas test required wherever gas-heated equipment is present, and an underground gas inspection covering burial depth, tracer wire and fittings. Henderson’s permit desk is 702-267-3620.
In unincorporated Clark County, which covers much of the valley including large parts of Spring Valley, Enterprise, Paradise and Summerlin South, a pool heater is not available as one of the county’s simple online permits, so the application runs through the Department of Building and Fire Prevention. Confirm the current requirement with them directly at 702-455-3000.
A rule that applies everywhere in the state: in Nevada, only licensed plumbers and electricians may do plumbing or electrical work, including homeowners working on their own homes. That is the City of Las Vegas’s own language, and it is the single most common thing we have to explain to someone who bought a heater online and expected to install it over a weekend.
If you are not sure which jurisdiction you are in, your address decides it, not your mailing city. A home with a Las Vegas mailing address can sit in unincorporated Clark County, which is a different building department with its own requirements. We work through that in detail in our guide to pool permit requirements across Clark County, Henderson and North Las Vegas.
Nevada follows the International Energy Conservation Code rather than writing its own pool rules. Clark County adopted the 2024 IECC effective January 11, 2026, and Henderson applies its 2024 code set to submittals received on or after January 2, 2026.
The pool section of that code is short and worth knowing, because two of its three requirements are things homeowners often want anyway. It requires that electric power to a heater be controlled by an on-off switch that is an integral part of the heater, that heaters and pump motors be on a time switch or equivalent automatic control, and that outdoor heated pools and permanent spas be provided with a vapor-retardant cover.
That last line is why a cover is not optional on a heated pool here. It is in the code, not a preference. And the time switch requirement is one more reason automation and heating tend to be specified together.
Worth being clear about what Nevada does not have: there is no Nevada equivalent of California’s Title 24 pool mandates. Pump efficiency is governed federally rather than by a state pool rule.
Edgewater has built pools in Southern Nevada for more than 50 years. Most of the heating calls we take are on pools somebody else built, and that is entirely fine. If you are also thinking about the wider pool, we handle equipment installation and replacement and full pool renovation as well.
A heater is only as good as the system around it. Three things determine whether the heat you pay for stays in the pool.
Circulation: Water has to move through the heater at the right rate for it to transfer heat efficiently. An undersized or badly scheduled pump undermines a correctly sized heater, which is another reason pump and heater decisions belong in the same conversation.
Water chemistry: Scale inside a heat exchanger acts as insulation. In water this hard, keeping calcium in range is not a cosmetic concern, it directly affects how long your heater lasts and how well it works. The same water chemistry decides how long your interior finish lasts as well, and our article on desert water quality and pool longevity covers why Las Vegas water is harder on equipment than most.
Leaks: A pool losing water is also losing heat, and in a climate with this much evaporation a slow leak hides easily behind what looks like normal loss. If your heater seems to be running more than it used to and chemistry is fine, that is worth investigating. We offer pool leak detection and repair across the valley.
Cold enough that most people stop swimming. We do not publish a water temperature figure because there is no authoritative month-by-month dataset for unheated pool water in Las Vegas, and we would rather not invent one. What is documented is the air: average overnight lows of 47.3 F in November, 39.6 F in December, 40.5 F in January and 44.1 F in February, per National Weather Service normals. Pool water follows that trend with a lag, and a pool that is not covered follows it faster.
They work, with reduced output. The Department of Energy’s guidance is that heat pump pool heaters work efficiently as long as the outside temperature stays above the 45 to 50 F range, and Las Vegas averages below that overnight from November through February. Jandy publishes the effect on its own JE series: 130,000 BTU and a COP of 6.0 under standard conditions, against 86,000 BTU and a COP of about 4.0 to 4.2 at 50 F air. A heat pump is an excellent choice for most of the Las Vegas year and a weak one for January on demand.
It depends on how you swim. Gas heats fast and works at any air temperature, which suits occasional and on-demand use, and suits any pool with a spa attached. A heat pump runs at 300 to 700 percent efficiency and suits frequent use across a long season. Many Las Vegas households are genuinely better served by a reverse-cycle heat pump that also chills the pool in July and August, which is a question gas cannot answer at all.
A reverse-cycle heat pump can. It runs the refrigeration cycle backwards to pull heat out of the water and reject it to the air. A gas heater cannot. With Las Vegas averaging overnight lows above 80 F in July and August, this is a far more useful feature here than in most of the country, and it is the single most overlooked option on a valley equipment pad.
In the City of Las Vegas, yes where gas piping between the meter and the appliance is installed, altered or repaired, and the city’s homeowner guide names pool heaters specifically. Henderson inspects gas heater installation and gas piping as part of its pool inspection sequence. In unincorporated Clark County, confirm with the Department of Building and Fire Prevention at 702-455-3000. In all jurisdictions, Nevada restricts gas and electrical work to licensed trades, homeowners included.
The Department of Energy formula is pool surface area multiplied by desired temperature rise multiplied by 12, giving required BTU per hour, with multipliers for a faster rise. Surface area matters more than gallons because surface area is where the heat leaves. Wind exposure, shade, target temperature and whether you will use a cover all move the answer, so we run the calculation on site.
Yes, and it is the highest-leverage item on the list. The Department of Energy calls covering a pool when not in use the single most effective means of reducing pool heating costs, with savings of 50 to 70 percent possible, plus 30 to 50 percent less make-up water and 35 to 60 percent less chemical consumption. The 2024 IECC also requires a vapor-retardant cover on outdoor heated pools, so on a heated pool it is a requirement rather than an upgrade.
It depends mostly on water chemistry and how much the unit runs. Hard water drives scale inside the heat exchanger, which insulates it and shortens its service life, and Las Vegas valley water is hard at 280 ppm. A heater kept in balanced water and serviced regularly outlasts one that is not, by a wide margin. We would rather assess yours than quote an average that may not describe your pool.
Yes. Most heater work we do is on existing pools built by other companies. We assess the equipment pad, gas service, electrical capacity and plumbing layout, then size from there.
On most pool and spa systems, yes. The valves determine which body of water the heater serves, and that is one of the functions automation handles best. It means you can bring the spa to temperature without heating thousands of gallons of pool alongside it.
Edgewater installs and services pool heating across Las Vegas, Henderson, Mesquite, North Las Vegas, Summerlin, Spring Valley, Enterprise, Paradise, Green Valley, Anthem, Boulder City and Centennial Hills.
If your heater has failed, if you are tired of a three-month swim season, or if your pool is too warm to enjoy in August, start with a site visit. See also Pool Builder Las Vegas, Pool Builder Henderson and Pool Builder Mesquite, or request an estimate.
Bill Edgington, Founder of Edgewater Custom Pools, Inc., designed and built the first Edgewater Pool in 1969. Since then, we have constructed over 6,000 pools and spas, mostly on a referral basis.